|
|
|
Who's Online
There currently are 6003 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I am very happy regarding the online purchase of this manual from Owner-Manuals.com as with this I could set right my Denon CD player and Amplifier.
I once again sincerely thank them for the prompt service which was rendered to me.
N. Shanker
;
More than pleased with my prurchase, very good product for the price.
;
Manual-link came 30 minutes after having paid for an extremely rare (40 years old) item (sony icr-120) and helped me to get the radio rework again. So really good help for me, fast and reliable delivery and -taken that into consideration- a very reasonable price for that service. So thanks again! Mike, Germany
 ;
Some of the pictures in this manual are a bit irritating. I had to dissassemble the unit and some of the screws have different threads, which is not mentioned in this manual. Also some of the drawings of the boards look different than the actual boards.
After all, the manual was very useful. I was able to recalibrate the capstan drive and it is working fine again.
;
This manual is very good. 303 pages scanned in a very high resolution. My camera has bad, leaking capacitors which all of the V5000 models are suffering from these days.
There is a huge part list with all capacitors, transistors etc. in this manual which helped me a lot. Otherwise I would not have been able to buy replacement parts.
The dissassembly guide is very enormous and detailed. Unlike on the Panasonic MS1 manual I downloaded here it actually looks like the real parts look. And the screws are labeled correctly, so you shouldn't have any left after the repair. ;)
Disassembly for Service
Back Cover
Remove all the screws marked with an arrow( from the back of the receiver. See Fig. 8. )
C-Board - CRT Output
Plugs into the socket on the CRT neck. To release the Focus wire, use a flat tool to release See Fig. 6 A, pull the wirethe tab in the socket, look up and remove the wire by pulling away the socket B, To re-insert, close the wire-look by pushing until is secured with the tab, and insert the wire into the socket
Note: Screw configuration, type, and number of screws vary depending on the model of the Receiver serviced and the application; various models are covered in this Manual. Use same hardware when reassembling the receiver.
� � � � 2 screws at the top edge of the Receiver. 2 screws at the lower corners of the Receiver. 1 screw by the A/V jacks. 1 screw by the Fly-back assembly.
A-Board - Main Chassis
1. Pull carefully the tab in the chassis rail, at the left side of the main chassis, this will release the rail from the cabinet. See Fig 5. 2. Slide the chassis and rail completely out of the guide rails of the cabinet. 3. Stand the receiver on its edge. The underside of the board is completely accessible for component replacement.
A
Figure 6. Focus Wire Release
B
Speakers
Speakers are secured to the cabinet�s front with 2 screws in diagonal (opposite corners).
Note: Some tie-wraps that secure the wire dressings may need to be unfastened for chassis removal.
4. When reassembly, place the chassis rail on the cabinet, then place the main chassis, be sure is in the rails at both sides, then push all the way to the front.
Keyboard Push Button Assembly
Fastened to the inside of the cabinet front with 1 or 2 screws, according to the model�s cabinet.
Disassembly for CRT Replacement
1. Discharge the CRT as instructed in the Safety Precautions (see page 2). 2. Disconnect the yoke (DY) plug and degaussing coil (DEG) plug from the main board. 3. Unplug the CRT 2nd anode button. 4. Remove the C-Board from the CRT base and unplug the black wire (CRT dag ground) C10. 5. Disconnect Speakers plug SP from the A-Board. 6. Lift the Main Chassis (A-Board) completely out with the CRT Board attached.
Figure 5. Chassis Rail Detail
- 10 -
|
|
|
> |
|
