|
Who's Online
There currently are 6021 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
;
This SM is quiet scarce and hard to find it is an excellent Service manual, very clear to read and to print schematics and diagrams, Hi quality, Complete manual with no pages missing. I am very pleased with the manual and the fast service I have received. Great place to shop.
Good luck finding you manual...
MC-UG383-00
and the plastic shaft. Pry out the plastic shaft as illustrated.
4. Carefully lift up on the agitator assembly until it clear both sides of the nozzle housing.
3.4.2.
Installation
5. Remove the nozzle housing as illustrated. 6. Remove the nozzle packing, window and handle release assembly.
1. Place the belt around the motor shaft. 2. Place the belt around the agitator pulley on the agitator assembly. NOTE: There is a place for the belt to fit on one end of the agitator assembly only. This is the agitator pulley. 3. Reassemble the new agitator assembly back into the nozzle housing by placing the side opposite the belt partially into the slot. The small tabs should be aligned against the nozzle and the other against the lower plate. This will hold the agitator in place and leave both hands free to place enough tension on the belt to allow that side of the agitator to return to the nozzle housing slot. 4. Use both hands to pull the belt tight, and slide the agitator assembly firmly into the slots on each end of the nozzle housing. 5. Rotate the agitator assembly by hand to insure nothing rubs and check for correct assembly. 6. Replace the lower plate as outlined in the LOWER PLATE REMOVAL/INSTALLATION section.
3.5.2.
Installation
1. Install the nozzle packing, if not already in place, window and handle release assembly in the new nozzle housing. 2. Fit the nozzle around the motor shaft side first, and rotate it into place on the dust container as illustrated.
3.5.
3.5.1.
Nozzle Housing Replacement
Removal
3. Slide the plastic shaft through the nozzle housing and into the dust container. Make sure that the slot on the bottom of the plastic shaft is down and seated onto the projection.
1. Remove the lower plate as outlined in the LOWER PLATE REMOVAL/INSTALLATION section. 2. Remove the belt and agitator assembly as outlined in the respective sections. 3. Remove the nozzle hose by pulling up on the hose to remove it from the nozzle housing. Pull the nozzle hose out of the back of the nozzle housing.
4. Insert a flat blade screwdriver between the nozzle housing 10
4. Reassemble the nozzle hose by inserting it into the nozzle
|
|
|
> |
|