|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Product was very good. Received quickly and complete
 ;
Although printing quality is not the best, the manual was very helpful in order to reactivate this ancient but still good electronic musical instrument.
;
as a first-time user and buyer from this site, i found the overall service outstanding!! this product is a godsend as, without it, i would never have been able to find my way around and use my machine as intended. i will certainly use this site again as required. many many thanx!!
;
This manual is exactly what I needed. This site always has every manual I need, and it is also much less expensive then most other sites. This is the only manual site I will use.
;
Useful manual, good scan, worth the pay if you find the unit difficult to operate.
Lamp Replacement
CAUTION: Because of the possibility of injury, strictly follow the replacement procedure below.
3 Remove the Lamp cover screws.
First read caution and warning labels on lamp cover. Then, remove the lamp cover screws (2) by using a screwdriver. Lamp cover screws
5 Insert the new lamp unit being careful of the
insertion direction. � Press on the arrow mark making sure insertion is done correctly.
2
Replace the new Air Filter unit. Slide the new air filter into the projection display so that the indentations of the filter and projection display are aligned. Then, press on the arrow mark place. until you hear it snap into
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>
Screwdriver
6 Replace the Lamp unit and cover screws.
Lamp cover handle CAUTION: [Under no circumstance should you touch the actual bulb.] At this high operating temperature the natural oil on your finger can cause the glass to weaken where touched and the bulb can crack or explode. Replace the lamp unit/cover screws with a screwdriver. � Properly dispose of old lamp.
� Lamp replacement procedure
1 Follow the �Turning the power on and off� steps.
After turning off the power, unplug the power cord from the wall outlet and confirm that the area around the lamp unit has cooled down. POWER button/POWER indicator
Note
Attach the lamp unit and lamp unit housing door securely. If the lamp unit and lamp unit housing door are not attached securely, the protective circuit will be activated and the power will not turn on.
After lamp replacement, follow the procedure below
Warning: Only perform lamp time reset when the lamp has been replaced.
� Lamp time reset procedure
1
4 Remove the lamp unit screws (2) with a
LAMP indicator � Please wait more than one hour for lamp replacement. [ If you need to replace the lamp more urgently ] � The Projection display has a forced cooling feature. After the POWER button is turned OFF, and during the first minute of the normal cooling fan operation, press the VOL+ button on the projection display and button on the remote control at same time for more than 5 seconds. The cooling fan operates for about 10 minutes. The LAMP indicator flashes red 5 times every 5 seconds.
screwdriver. Then, grasp the lamp unit as shown in the diagram, and slowly remove from the projection display. � Do not drop, as the impact of dropping may cause the lamp to explode. Lamp unit screws
7 Replace the left Speaker cover.
Be sure the power cord is plugged into a properly grounded wall outlet. Then, press the POWER button on the projection display or the remote control to turn the power on. While pressing the VOL- button on the projection display, hold down the PIP button on the remote control at same time for more than 5 seconds.
Air Filter Replacement
The replacement lamp comes with an air filter. When replacing the lamp, also replace the air filter at the same time.
2
Note
For the procedure to clean the air filter, please refer to the operating instructions. and
� Air Filter replacement procedure
1 Remove the Air Filter unit
Grasp the indented portion of the air filter and pull it out of the projection display. Lamp unit handle WARNING: The lamp may be hot. Be careful when handling. CAUTION: � High-pressure lamp may explode if improperly handled. � Danger of injury due to glass fragments. Indent
3
2 Remove the left Speaker cover.
Place your fingertips under the left speaker panel and pull it from the projection display.
When reset procedure is complete, the screen on the right will appear.
L AMP T I ME WAS RE S E T TO 0 .
RECALL
EXIT
Note
� When lamp time reset is finished, the LAMP indicator goes out.
LSQC0291
|
|
|
> |
|
