PANASONIC WVCW374
Owner's Manual

I Preparations
The camera can be mounted either of the following ways. � Using the supplied adapter box. � Fixing the camera mounting arm directly Caution: When installing, the power cord is NOT to be exposed to outdoor conditions like frost and sunlight.

Fixing the camera, camera mounting arm, and adapter box
As the factory default, the camera head has been tilted to the downside. 1. Move the camera head, as shown in the illustrations, by loosening the tilting lock screw.

To facilitate wirings, it is recommended to align two junction boxes.
83.5 mm {3-5/16"} Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)} 46 mm {1-13/16"}

W374 WV-C

Color CCTV Camera

DII S

Instructions
Using the supplied adapter box
When you mount the camera on a flat wall with a cable access hole, or through exposed wirings,
Camera head
DII S
74 3 W V-C W

Junction box Mounting arm

Model No.

WV-CW374

you will use the supplied adapter box. For installation, refer to Installation of Camera and Adapter Box. Notes: � Mounting screws are not supplied. Prepare locally procured screws matching the material, structure, and total weight of mounting place. � Screws to fix the camera mounting arm to the adapter box are supplied.

Tilting lock screw (Hexagon socket screw)

Mounting screws (Locally procured) x 4

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. N0504-0 3TR002485AAA Printed in Japan

2. After adjustment, tighten the tilting lock screw again. 3. Attach the camera mounting arm to the left or right hinges of adapter box, so that the mounting arm can be opened and closed flexibly. (Refer to the illustration in Step 4.)

I Waterproof Process
Apply waterproofing to the necessary portions, using appropriate materials. This camera is applied to IP66 only when installed according to the instructions in this document, and appropriate waterproofing is applied. Screw-holes, cable access holes, and gaps: Fill these portions with silicon rubber or equivalent waterproofing material. Note: The waterproof process should be made by qualified service personnel or system installers according to the local requirement.

Fixing the supplied camera mounting arm directly
� You can fix the camera mounting arm to a junction box installed on the wall. � You can fix the camera mounting arm directly to the wall with a cable access hole. For installation, refer to Fixing the Mounting Arm Directly. Note: Attach the mounting arm to hinges on the side opposite to the wall. 4. Fix the camera to the camera mounting arm.
Fixing screw for adapter box (Supplied) x1 (M4 x 35)

Caution: Before attempting to connect or operate this product, please read the marking on the top.
For U.S.A

Note: Mounting screws are not supplied. Prepare locally procured screws matching the material, structure, and total weight of mounting place.

CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user�s authority to operate this equipment.

Camera

I Installation of Camera and Adapter Box
Notes: � For outdoor use, the mounting screws and screw holes require waterproofing. Refer to Waterproofing Process in this document. � When wiring the camera cables through the adapter box, use a cable access hole. The cable access hole is G3/4.
SDII

Fixing screws for camera (Supplied) x 3 (M4 x 8)
W W V-C 374

I Fixing the Camera Mounting Arm and Adapter Box
Hinges

1. Fix the camera mounting arm to the adapter box with four supplied screws. 2. Fix the mounting arm covers to the mounting arm with two supplied screws.
Adapter box

Installing the adapter box directly to the wall
With the mounting screws (locally procured), fix the adapter box to a junction box or directly to the wall. Note: Lead the camera cables out of the cable hole of mounting arm.
46 mm {1-13/16�} Cable access hole Adapter box Mounting arm Mounting arm

The lightning flash with arrowhead symbol, within an equilateral triangle, is interned to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient SA 1965 magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

5. Pass the cables through the cable clamp of mounting arm, and then to the wall.

The serial number of this product may be found on the top of the unit. You should note the serial number of this unit in the space provided and retain this instruction as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No.

Hole 6 mm (W) x 10 mm (H) {1/4� (W) x 13/32� (H)}
374 W WV-C

83.5mm {3-5/16"}

SA 1966

Center of adapter box

{3-5/16"}

DII S

22 mm 24.5 mm

WARNING: All work related to the installation of this product should be made by qualified service personnel or system installers. CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm {0.12"} in each pole shall be incorporated in the electrical installation of the building.
Cable clamp Mounting screws (Locally procured) x 4 Cable access hole Adapter box (Used for wiring) (G3/4" internal thread) {14/16"} {31/32"}

Fixing screws for adapter box and mounting arm (Supplied) x 4 (M5 x 20)

Fixing screws for covers (Supplied) x 2 (M3 x 6)

Covers x 2

Note: Do not expose the cables to sunlight.
83.5 mm

Installing the adapter box to a junction box

I Adjusting the Camera Angle I Fixing the Mounting Arm Directly
Notes: � For outdoor use, the mounting screws and screw holes require waterproofing. Refer to Waterproof Process in this document. � Avoid waterproofing the drainage hole. 1. Remove the rear cover by loosening the fixing screw.

I Preface
Panasonic WV-CW374 is designed for installation on the wall, using a camera mounting arm or the supplied adapter box.

To facilitate wirings, it is recommended to align two junction boxes.

46 mm {1-13/16"} Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)}

I Precautions
� Refer all work related to the installation of this product to qualified service personnel or system installers. � Do not operate the appliance beyond its specified temperature, humidity, or power source ratings. Use the camera at temperatures between �30 °C and +50 °C {between �22 °F and 122 °F}, and humidity below 90 %. The input power source for this appliance is 12 V DC/24V AC 60 Hz for WV-CW374. When you install the camera in a low-temperature location and start operating it, it may take time (around 30 minutes) for the inside of the camera to warm up. Cut power once then supply power again. � Screws to mount the camera is not supplied. Prepare locally procured screws matching the material, structure, and total weight of mounting place. � Be sure to use a ceiling board having enough strength to support this camera.

Mounting arm

(2) Remove the rear cover. (1) Remove the fixing screw.

Drainage hole Junction box

With the mounting screws (locally procured), fix the camera mounting arm directly to a wall or a junction box installed on the wall.

2. Remove the switch cover by loosening the two fixing screws. The switch unit will appear.

24.5 mm

CAUTION

Mounting screws (Locally procured) x 4

Hole 6 mm (W) x 10 mm (H) {1/4" (W) x 13/32" (H)}

46 mm {1-13/16"} Cable access hole

(1) Remove the fixing screw. (x 2)

{31/32"}

(2) Remove the switch cover.

W W V-C

374

SD

II

Mounting screws (Locally procured) x 4

83.5 mm {3-5/16"}

Mounting arm